[Home]Stepper Drive Timing

LinuxCNCKnowledgeBase | RecentChanges | PageIndex | Preferences | LinuxCNC.org
Difference (from prior major revision) (no other diffs)

Added: 75a76
||*Aliexpress etc.||TB6600 Fake (TB67S109)||5000||5000||?||?||Rising Edge||https://toshiba.semicon-storage.com/info/TB67S109AFTG_datasheet_en_20190228.pdf?did=14642&prodName=TB67S109AFTG||
This page is for step and direction timing of stepper drives.
The timing info is correct AFAIK.
Please add to this list using the stepconf wizard format and in nanoseconds so it will be uniform.
If you want to add information to this page or add a new page, follow some BasicSteps.
Some boards have know issues see the troubleshooting hardware page Hardware Problems

If your unsure about your drive timing start high like 10000 for each and test. remember that signal conditioning and opto-isolation can increase timing requirements. That's why you need to know the timings for a driver board, not just the step translator chip that is contains. Also notice that some controllers step on the falling edge some on the rising edge. This matters as it will change the timing and will be hard to trace. make sure LinuxCNC follows what the controller expects.

Note 1 if an asterisk precedes the name then the values are not confirmed. If you can confirm the values please do...

Times listed are in nanoseconds (ns). Multiply microseconds (us) by 1000 to get nanoseconds (ns)

ManufacturerModelStep TimeStep SpaceDirection HoldDirection SetupSteps onSpec Sheet
Chinese Blue BoardsTB6560 CNC Stepper Motor Driver Controller Board150000150000150000150000Falling Edgehttp://hyu68.com/cp8.htm
Gecko2015004000200001000Falling Edgehttp://www.geckodrive.com/support/motor-control-manuals/stepper-drives/g201-rev-16.html
Gecko2025004500200001000Falling Edgehttp://www.geckodrive.com/support/motor-control-manuals/stepper-drives/g202-rev-15.html
Gecko203v10002000200200Rising Edgehttp://www.geckodrive.com/support/motor-control-manuals/stepper-drives/g203v-rev-7.html
Gecko201x5003000200001000Falling Edgehttp://www.geckodrive.com/support/motor-control-manuals/stepper-drives/g201-rev-16.html
Gecko2125004000200001000Falling Edgehttp://www.geckodrive.com/support/motor-control-manuals/stepper-drives/g212-rev-15.html
Gecko213v20001000200200Rising Edgehttp://www.geckodrive.com/support/motor-control-manuals/stepper-drives/g213v-rev-7.html
Gecko3203500500200200Rising Edgehttp://www.geckodrive.com/support/motor-control-manuals/dc-servo-drives/g320-rev-7.html
Gecko320x10002500200200Rising Edgehttp://www.geckodrive.com/support/motor-control-manuals/dc-servo-drives/g320x-rev-10.html
Granite DevicesVSD-E/XE Evolution125125125125Rising Edgehttp://granitedevices.fi/assets/files/vsd-e_160_manual.pdf
Granite DevicesVSD-E/XE DualDC1501850150800Rising Edgehttp://granitedevices.fi/assets/files/vsd-e_160_dualdc_manual.pdf
JVLSMD4150050025002500Rising Edgehttp://www.jvl.dk/files/pdf/lb043gb.pdf
JVLSMD4250050025002500Rising Edgehttp://www.jvl.dk/files/pdf/lb043gb.pdf
Linistepper Open SourceRULMS13000010000040004000Rising Edgehttp://www.piclist.com/techref/io/stepper/linistep/index.htm
Linistepper Open SourceTHB60642300230046001000Rising Edgehttp://www.piclist.com/techref/io/stepper/THB6064/index.htm
*Motion ControlMSD542>1500200020002000Rising Edgehttp://www.motioncontrolproducts.com/c2/uploads/msd542%20datasheet.pdf
ParkerOEM7502003000200000Rising Edgehttp://www.compumotor.com/manuals/OEM750/OEM750_Entire_Rev_B.pdf
STL297?50040001000Rising Edgehttp://www.st.com/stonline/books/pdf/docs/1334.pdf
XylotexXS-3525/8S-320001000200200Rising Edgehttp://www.xylotex.com/XS3525V202.pdf
XylotexXS-3525/8S-410001000200200Rising Edgehttp://www.xylotex.com/XS3525V400.pdf
Lin EngineeringSilverpak 17D/DE2000020000200200Rising Edgehttp://www.linengineering.com/site/products/pdf/SilverPak17D_DE-manual.pdf
HobbycncPro Chopper Board2000200020002000?http://www.hobbycnc.com/products/hobbycnc-pro-chopper-driver-board-kits/
*Routout2.5amp Stepper Driver20010001000??http://www.routoutcnc.com/2-5ampdriver.pdf
*Intelligent Motion SystemIM4831000100010001000Rising Edgehttp://www.imshome.com/im483.html
Keling4030500050002000020000?http://www.
Keling6852175017501000010000Rising Edgehttp://www.kelinginc.net/kL-6852.pdf
Sherline 8760100060002400024000?http://www.sherline.com/
Burkhard Lewetz Step3S600015000?5000?http://www.lewetz.de/download/ibstep3se.pdf
Parker CompumotorZeta 4200200?(200)?(200)Rising Edgehttp://www.compumotor.com/manuals/ZETA/ZETA_Rev_A_Entire.pdf
www.cncdrive.comDugong1000250010001000?http://www.cncdrive.com/content/dugong.htm
www.cncdrive.comDG2S-080201000250010001000?http://cncdrive.com/DG2S_08020.html
Wantai MotorsDQ542MA50505050500500?http://www.wantmotor.com/ProductsView.asp?id=257&pid=82
Leadshine USADigital DM422 40V 2.2A75007500200005000Rising Edgehttp://leadshineusa.com/UploadFile/Down/DM422m.pdf
Leadshine USADigital DM556 50V 5.6A25002500100005000Rising Edgehttp://leadshineusa.com/UploadFile/Down/DM556m.pdf
Leadshine USADigital DM856 80V 7.0A25002500100005000Rising Edgehttp://leadshineusa.com/UploadFile/Down/DM856m.pdf
Leadshine USADigital DM870 80V 7.0A25002500100005000Rising Edgehttp://leadshineusa.com/UploadFile/Down/DM870m.pdf
Leadshine USADigital DM1182 150VAC 8.2A25002500100005000Rising Edgehttp://leadshine.com/UploadFile/Down/DM1182m.pdf
Leadshine USADigital EM402 40V 2.2A100002500100005000Rising Edgehttp://leadshine.com/UploadFile/Down/EM402d_P.pdf
Leadshine USADigital EM503 50V 4.2A25002500100005000Rising Edgehttp://leadshine.com/UploadFile/Down/EM503d_P.pdf
Leadshine USADigital EM705 70V 7.0A25002500100005000Rising Edgehttp://leadshine.com/UploadFile/Down/EM705d_P.pdf
Leadshine USADigital EM806 80V 8.2A25002500100005000Rising Edgehttp://leadshine.com/UploadFile/Down/EM806d_P.pdf
Leadshine USAAnalog M415B 40V 1.5A1500150080005000Rising Edgehttp://leadshineusa.com/UploadFile/Down/M415Bm.pdf
Leadshine USAAnalog M542 50V 4.2A1500150080005000Rising Edgehttp://leadshineusa.com/UploadFile/Down/M542V2m.pdf
Leadshine USAAnalog M752 75V 5.2A1500150080005000Rising Edgehttp://leadshineusa.com/UploadFile/Down/M752m.pdf
Leadshine USAAnalog M880A 80V 7.8A1500150080005000Rising Edgehttp://leadshineusa.com/UploadFile/Down/M880Am.pdf
Leadshine USAAnalog M860H 80VAC 7.2A1500150080005000Rising Edgehttp://leadshineusa.com/UploadFile/Down/MA860Hm.pdf
Leadshine USABrushed servo DCS303 30V 15A25002500100005000Rising Edgehttp://leadshineusa.com/UploadFile/Down/DCS303m.pdf
Leadshine USABrushed servo DCS810 80V 20A25002500100005000Rising Edgehttp://leadshineusa.com/UploadFile/Down/DCS810V1m.pdf
Leadshine USABrushed servo DCS810S 80V 20A1000100070005000Rising Edgehttp://leadshineusa.com/UploadFile/Down/DCS810Sm.pdf
Leadshine USABrushless servo ACS306 30V 15A25002500100005000Rising Edgehttp://leadshine.com/UploadFile/Down/ACS306hm.pdf
Leadshine USABrushless servo ACS606 60V 15A85085067005000Rising Edgehttp://leadshineusa.com/UploadFile/Down/ACS606m.pdf
Leadshine USABrushless servo ACS806 80V 20A85085067005000Rising Edgehttp://leadshineusa.com/UploadFile/Down/ACS806m.pdf
PololuA4988 Stepper Motor Driver Carrier10001000200200Rising Edgehttp://www.pololu.com/catalog/product/1182/
PololuDRV8825 Stepper Motor Driver Carrier19001900650650Rising Edgehttp://www.pololu.com/catalog/product/2132/
cnc4youCW50452000800050005000Rising Edgehttp://cnc4you.co.uk/resources/CW5045.pdf
*Aliexpress etc.TB6600 Fake (TB67S109)50005000??Rising Edgehttps://toshiba.semicon-storage.com/info/TB67S109AFTG_datasheet_en_20190228.pdf?did=14642&prodName=TB67S109AFTG

LinuxCNCKnowledgeBase | RecentChanges | PageIndex | Preferences | LinuxCNC.org
This page is read-only. Follow the BasicSteps to edit pages. | View other revisions
Last edited December 9, 2022 12:02 am by LOSchliefkowitz (diff)
Search:
Published under a Creative Commons License