[Home]History of Gmoccapy Plasma

LinuxCNCKnowledgeBase | RecentChanges | PageIndex | Preferences | LinuxCNC.org
Revision 31 . . March 30, 2014 3:38 pm by Mariusl [*Typos]
Revision 30 . . December 29, 2013 7:47 pm by Mariusl
Revision 29 . . December 29, 2013 7:46 pm by Mariusl
Revision 28 . . December 29, 2013 7:45 pm by Mariusl
Revision 27 . . December 29, 2013 7:37 pm by Mariusl
Revision 26 . . December 29, 2013 7:20 pm by Mariusl
Revision 25 . . December 29, 2013 7:17 pm by Mariusl
Revision 24 . . December 29, 2013 7:05 pm by Mariusl
Revision 23 . . December 29, 2013 6:09 pm by Mariusl
Revision 22 . . December 29, 2013 6:08 pm by Mariusl
Revision 21 . . December 29, 2013 5:49 pm by Mariusl
Revision 20 . . December 29, 2013 5:48 pm by Mariusl
Revision 19 . . December 29, 2013 5:47 pm by Mariusl
Revision 18 . . December 29, 2013 5:46 pm by Mariusl
Revision 17 . . December 29, 2013 5:41 pm by Mariusl
Revision 16 . . December 29, 2013 5:40 pm by Mariusl
Revision 15 . . December 29, 2013 5:21 pm by Mariusl
Revision 14 . . December 29, 2013 7:21 am by Mariusl
Revision 13 . . December 28, 2013 12:49 pm by Mariusl
Revision 12 . . December 28, 2013 12:48 pm by Mariusl
Revision 11 . . December 28, 2013 12:47 pm by Mariusl
Revision 10 . . December 28, 2013 12:31 pm by Mariusl
Revision 9 . . December 28, 2013 12:16 pm by Mariusl
Revision 8 . . December 28, 2013 11:01 am by Mariusl
Revision 7 . . December 28, 2013 10:46 am by Mariusl
Revision 6 . . December 28, 2013 10:44 am by Mariusl
Revision 5 . . December 28, 2013 10:31 am by Mariusl
Revision 4 . . December 28, 2013 9:35 am by Mariusl
Revision 3 . . December 28, 2013 9:19 am by Mariusl
Revision 2 . . December 28, 2013 9:07 am by Mariusl
Revision 1 . . December 28, 2013 8:45 am by Mariusl
  
Difference (from prior major revision) (author diff)

Changed: 22c22
When cutting metal with a flame, the uneven heating up of the metarial will cause the sheet to bend and buckle. To start with, most sheets of metal does not come out of the mill or press in a very even or flat state. Thick sheets (30mm plus) can be out of plane as much as 50mm to 100mm.
When cutting metal with a flame, the uneven heating up of the material will cause the sheet to bend and buckle. To start with, most sheets of metal does not come out of the mill or press in a very even or flat state. Thick sheets (30mm plus) can be out of plane as much as 50mm to 100mm.
LinuxCNCKnowledgeBase | RecentChanges | PageIndex | Preferences | LinuxCNC.org
Search:
Published under a Creative Commons License